How To Open Iget Bar Plus?

The IGET Bar Plus is designed as a sealed, single-use unit for safety and reliability. It is not intended to be opened by the user. Tampering with the device can damage internal components, cause leakage, and poses significant safety risks, including potential battery failure.

However, if you need to access the interior for responsible battery disposal or are troubleshooting a non-functional device, follow this extremely cautious guide at your own risk.

⚠️ Critical Safety Warnings First

Do Not Pierce or Crush: Never use excessive force, stab, or crush the device.
Battery Hazard: The internal lithium-ion battery can catch fire or explode if punctured, short-circuited, or damaged.
Liquid Contact: The internal capacity may leak. Avoid contact with skin and eyes.
Irreversible Damage: Opening the device will permanently ruin it. It cannot be refilled or reused.

If You Must Proceed: Step-by-Step Instructions

Tools Needed: Small flat-head screwdriver, protective gloves, safety glasses, and a clean, dry workspace.

Step 1: Locate the Seam
Examine the mouthpiece end of the IGET Bar Plus. You will find a thin, circular seam where the outer shell meets the inner chassis.

Step 2: Gently Insert a Lever
Place the tip of your small flat-head screwdriver into this seam. Apply very gentle, steady pressure to pry the outer casing away from the inner assembly.

Step 3: Separate the Shell
Slowly work your way around the seam. The outer shell should begin to separate. Continue until you can carefully lift it off, revealing the internal tank and battery assembly.

Step 4: Handle Internals with Care
Inside, you will see:

A silicone seal holding the mouthpiece.
The central chimney connected to the tank.
The battery attached with wires.
The cotton-wicked tank containing the remaining capacity.

Step 5: For Battery Removal (Disposal)
If your goal is to remove the battery for separate recycling, carefully disconnect the thin wires soldered to the battery terminals using wire cutters. Place tape over the battery terminals immediately after cutting to prevent short circuits. Take the isolated battery to a designated e-waste or battery recycling facility.

The Responsible Alternative

Instead of opening the device, we strongly recommend the following:

For a Device That Seems Faulty: If your IGET Bar Plus is not working properly upon arrival, contact your retailer immediately. A reputable seller like iGetBaroz will have a support process to address genuine issues with authentic products.
For End-of-Life Disposal: Once the device is depleted, do not throw it in regular household trash. The entire unit should be taken to a local electronic waste (e-waste) recycling centre that accepts lithium batteries.

Need a Reliable Replacement?

If you are trying to open your device because it failed prematurely, it’s crucial to source authentic products from authorised retailers. Counterfeit or poorly manufactured devices have much higher failure rates.

For guaranteed authentic IGET products and reliable customer support, consider visiting iGetBaroz{:target=”_blank”}, an authorised Australian distributor focused on product authenticity and customer safety.

Remember: Your safety is paramount. When in doubt, do not open the device and seek professional guidance.

How to Open IGET Bar Plus: Important Notes & Step-by-Step Guide (Educational Purposes Only)

Critical Pre-Disclaimer: The IGET Bar Plus is purpose-built as a single-use disposable vape device, intended to be discarded once the e-liquid is exhausted or the battery dies. Opening the device is not endorsed by the manufacturer, as it may void any warranty, expose you to safety risks (like lithium-ion battery hazards or e-liquid irritation), and compromise the device’s integrity. If you’re facing issues with your IGET Bar Plus, contact authorized retailer iGetBaroz for support or replacement instead of attempting to open it.

If you still wish to open the device for troubleshooting or educational reasons, follow these steps with extreme caution:

Gather Safe Tools
Use non-conductive tools to avoid shorting the battery: a plastic pry tool, small flathead screwdriver (wrapped in tape to prevent scratches), and precision tweezers. Avoid sharp metal tools that could puncture internal components.

Locate the Seam
The IGET Bar Plus has a tight snap-fit seam between the mouthpiece section and the main battery/e-liquid chamber. Run your finger along the edge to find the thinnest gap, usually near the base of the mouthpiece.

Gently Pry the Casing
Insert the plastic pry tool into the seam and apply steady, gentle pressure to create a small gap. Work the tool around the entire edge of the mouthpiece, twisting slightly to separate the two plastic halves. Do not force it—excessive pressure may crack the casing or puncture the e-liquid pod.

Access Internal Components
Once the top section is removed, you’ll see the sealed e-liquid pod connected to a lithium-ion battery module. The pod is typically glued in place; do not attempt to puncture or remove it, as e-liquid (especially nicotine variants) can be toxic if absorbed through the skin or ingested.

Reassemble (If Applicable)
To close the device, align the plastic halves and press firmly until they snap back into place. Note that the airtight seal may be compromised, leading to leakage or reduced performance.

Non-Negotiable Safety Precautions

Battery Danger: Lithium-ion batteries can catch fire or explode if damaged, punctured, or short-circuited. Never modify or remove the battery from the IGET Bar Plus.
E-Liquid Hazards: Capacity contains irritants (and nicotine in most models). Wear gloves if handling internal parts, and rinse skin immediately if exposed.
Warranty Void: Opening the device will instantly invalidate any manufacturer or retailer warranty. For faulty devices, reach out to iGetBaroz—their team offers reliable after-sales support for authentic IGET products.

If you prefer a reusable vaping option, explore IGET’s pod-based systems via iGetBaroz, but remember the Bar Plus is strictly designed for single-use.