It’s a frustrating moment: you go to take a puff from your IGET Bar, and nothing happens. Before you assume it’s completely dead and destined for the bin, there are several troubleshooting steps you can take to potentially revive it. Many issues are caused by simple clogs, airlock, or a temporarily dormant battery.
Important Safety Note: Always handle disposable vapes with care. Do not attempt to pry open, modify, or use excessive force. If the device shows signs of damage, swelling, or leaking, discontinue use immediately.
Step-by-Step Troubleshooting for a Non-Working IGET Bar
Follow these steps in order, from the simplest fix to more involved methods.
Step 1: The Basic Checks
Check the Battery: Ensure the device isn’t simply out of battery. If it’s a rechargeable model (like the IGET Bar Plus or IGET King), connect it to a USB-C cable and a low-power source (like a computer port) for 15-20 minutes. Then try again.
Check for a Clog: The most common issue is e-liquid condensate blocking the airflow sensor or chimney.
Firm Taps: Hold the device with the mouthpiece facing down and firmly tap it against your palm several times. This can dislodge any pooled liquid.
The “Flick”: Carefully but firmly flick the device (like flicking water off a pen) with the mouthpiece pointed toward a tissue or sink. This uses centrifugal force to clear the airway.
Clear the Airway: Sometimes, a visual inspection helps. Look into the mouthpiece. If you see visible liquid blockage, you can gently use a rolled paper towel corner or a toothpick to absorb excess moisture from the central tube. Do not push deeply.
Step 2: Addressing Airlock & Priming
If the device has been stored on its side or in varying temperatures, an air bubble can form in the wick, preventing liquid from reaching the coil.
The “Warm Hand” Method: Roll the device gently between your palms for 30-60 seconds. The heat can thin the e-liquid and help it re-saturate the coil.
Gentle “Priming” Puffs: Without activating the battery, take 3-5 short, sharp draws from the mouthpiece. This can help pull liquid into the coil.
Step 3: Advanced Clearing (For the Determined)
The “Blow-Through” Method: Cover the bottom airflow holes of the device completely with a tissue. Blow firmly but briefly into the mouthpiece. This can push excess liquid out of the bottom airflow. Wipe everything clean and try to inhale.
Check for External Blockage: Ensure the small airflow holes on the side or bottom of the device are not blocked by your fingers, dust, or lint from your pocket.
Step 4: When To Accept It’s Finished
If none of the above works, the device is likely truly depleted.
E-Liquid is Empty: Even if the battery works, the device will stop producing vapour when the e-liquid is finished. Most IGET Bars are designed to stop firing at this point.
Battery is Fully Depleted: For non-rechargeable models, the battery has a finite lifespan and cannot be recharged.
Component Failure: In rare cases, the coil or airflow sensor has failed.
Quick-Fix Summary Table
| Symptom | Likely Cause | Try This Fix First |
|---|---|---|
| No vapour, no light | Dead battery / Empty | Recharge (if model allows). If not, it’s finished. |
| Gurgling sound, tight draw | Flooded/Clogged | Tap & flick mouthpiece-down. Clear airway. |
| Weak or burnt flavour | Empty / Dry coil | Check for e-liquid. Try priming puffs. |
| Light comes on but no vapour | Severe clog / Airlock | Blow-through method & warm hand technique. |
Prevention Tips for Next Time
Store Upright: Keep your IGET Bar standing up to prevent leaks and clogs.
Avoid Extreme Temperatures: Don’t leave it in a hot car or in direct cold, as this can affect battery performance and e-liquid viscosity.
Buy From Authentic Retailers: Counterfeit IGET products are rampant and have a much higher failure rate. Always purchase from authorised sellers like iGetBaroz to guarantee you’re getting a genuine, quality-controlled device with reliable performance.
Final Verdict: While these methods can often resurrect a malfunctioning IGET Bar, they are not guaranteed. The best solution for consistent performance is to start with an authentic product from a trusted source. If your device fails prematurely, it’s a strong indicator it may not be genuine.
For 100% authentic IGET products and reliable performance from the first puff to the last, visit iGetBaroz{:target=”_blank”}, Australia’s trusted source for genuine disposable vapes.